
Fireproofing and Firestopping in Saskatoon, Documented for Inspection
MAGNUS sprays fire protection onto steel and seals rated walls and floors. We work on commercial and public buildings across Saskatchewan. This work gets inspected, so we record it as it goes in.
We measure before we quote.
Mon–Fri, 8am–5pm
- Award-Winning Contractor
- Licensed & Insured
- 7,000+ Projects Completed
- Free Consultation
- Financing Available
- Serving Saskatoon & Surroundings Since 2008
What our customers say
At a glance
Fireproofing protects the frame, so steel keeps its strength long enough for people to get out. Firestopping seals the holes where pipes, ducts and cables pass through a rated wall or floor. Both get checked against a tested design. Both fail if the detail does not match.
Free
Consultation to talk your job through
Photos
Send photos and a specialist will reach out
Financing
Available, ask at your consultation
Since 2008
Insulating and repairing Saskatchewan buildings
Service area: Available in Saskatoon and within 50 km of the city, including Warman, Martensville and Delisle.
Signs you need fireproofing & firestopping
Any opening through a rated assembly defeats the rating it was built for.
Material knocked off during other trades leaves the member unprotected.
The point at which spray-applied protection goes on the frame.
A rated wall has been marked incomplete or wrong.
New services through an existing assembly need rated seals.
Work may be correct but cannot be demonstrated without records.
Need fireproofing or firestopping scoped on a Saskatchewan project? Send the drawings and we will price it. Call (306) 880-2878 · Mon–Fri, 8am–5pm
How long it takes
| Structural fireproofing | One to three weeksDepends on the steel area covered |
|---|---|
| Firestopping package | Several days to weeksDriven by penetration count |
| Remedial work | One to three daysTypical deficiency correction |
Timeframes are typical for a straightforward job and are confirmed at the consultation.
How we handle fireproofing & firestopping
Review the rated assemblies
We work from the drawings and the specified assemblies, since the tested detail is what an inspector checks against.
Coordinate with other trades
Penetrations are sealed after services are in but before finishes close them up, so sequencing matters.
Install to the tested detail
We spray protection on to the set thickness. Each seal is matched to the pipe or duct and the wall it passes through.
Document every location
Locations, systems and product data are recorded as installed, so the project file supports the inspection.
Ready to sort out your fireproofing & firestopping?
Serving Saskatoon. The consultation is free and there is no obligation.
What it costs
Fireproofing is priced by the area of structure covered and the rating required. Firestopping is priced by penetration count and type. Both are quoted from drawings, and both include the documentation the project file needs.
| Rating required | Higher ratings need greater thickness |
|---|---|
| Area of steel | The main driver on spray-applied fireproofing |
| Penetration count and type | Each service type uses a different tested system |
| Access and height | Lift and staging requirements affect labour |
| Schedule and sequencing | Coordination around other trades on an active site |
We do not publish fixed prices, because the number depends on what the consultation finds.
What you get with MAGNUS
Tested assemblies
Installed to the tested detail, which is what the inspector checks.
Documented as installed
Locations and product data recorded for the project file.
Licensed and insured
Business licence on file and full liability coverage.
Site-schedule aware
Sequenced after services and before finishes close the work in.
Free quotations
Priced from drawings at no cost.
Local and seasonal factors in Saskatoon
MAGNUS has done fire protection alongside insulation for years. Both often sit on the same walls, and pass through the same holes.
One trade doing both closes the gaps where faults show up at inspection. Nothing falls between two crews.
Common Questions
What is the difference between fireproofing and firestopping?
Fireproofing protects structural members, usually steel, so they hold their strength during a fire. Firestopping seals openings where pipes, ducts and cables pass through a fire-rated wall or floor, so flame and smoke cannot travel through the gap.
Why does firestopping fail inspection?
Most commonly because the installed detail does not match a tested system, the wrong product was used for that penetration type, or the work is correct but undocumented. Inspectors check against tested assemblies, so close is not sufficient.
When is fireproofing applied during construction?
Spray-applied protection goes on after the structure is erected and generally before the assemblies are closed in. Firestopping comes later, once services are run through the rated walls and floors but before finishes cover them. Getting that sequence wrong is expensive, because reopening a closed assembly to firestop it costs far more than doing it in order.
Frequently asked questions
Yes, remedial work is common. Material gets knocked off during mechanical and electrical installation, and it has to be made good before close-in. We can price it as a discrete package on an active site. Catching it before close-in matters, since correcting protection behind a finished ceiling means opening the ceiling again.
Yes. Locations, systems used and product data are recorded as the work goes in. Reconstructing that record afterward is far harder, which is why it is captured at the time of installation. Photographs of each location are included, which is what an inspector generally wants to see alongside the product data.
Yes. Renovation and remedial firestopping in occupied buildings is regular work. Access, sequencing and dust control are planned with the building manager before the crew starts. Working after hours or in phases is normal on these projects, so tenants and staff are disrupted as little as possible.
It depends on the rating specified and the member being protected. The tested assembly sets the figure, not a general rule. It is confirmed from the drawings at quotation and verified during installation. Substituting a thinner application to save material is exactly what fails an inspection, so the specified figure is what goes on.
Yes, and that is a common arrangement. Both scopes often sit on the same walls and involve the same penetrations, so running them under one subcontractor reduces the gaps where deficiencies usually appear. It also means one point of contact for the project file, rather than chasing documentation from two separate subcontractors.
Related services
Commercial Spray Foam
Large-scale spray foam for warehouses, shops, agricultural buildings and cold storage.
Commercial Spray Foam detailsSpecial Coatings & Waterproofing
Protective coatings and waterproof membranes for foundations, parkades, decks and concrete.
Special Coatings & Waterproofing detailsAsbestos Abatement
Asbestos testing, sample collection and contained removal, so renovations start safely.
Asbestos Abatement detailsSee the full range on our Saskatoon insulation and building envelope services page, or book a free consultation.
Industry leaders in comfortable, healthy & efficient buildings
Get fireproofing & firestopping priced properly
We offer full consultations. With 7,000+ projects completed, we have seen it all and can often diagnose from photos. Send us photos and a specialist will reach out. If an on-site consultation is needed, they will let you know. Mon–Fri, 8am–5pm.