Free consultations across Saskatoon and Saskatchewan
Batt insulation installed through the walls of a steel shop

Fiberglass and Mineral Wool Insulation in Saskatoon, Installed to Spec

MAGNUS installs fiberglass and mineral wool batts, including Rockwool (formerly Roxul), with vapour barrier across Saskatoon, in new builds, renovations and basement developments. Batts are the cost-effective choice where the cavity is clean, square and accessible.

Book a free consultation

We measure before we quote.

Mon–Fri, 8am–5pm

  • Award-Winning Contractor
  • Licensed & Insured
  • 7,000+ Projects Completed
  • Free Consultation
  • Financing Available
  • Serving Saskatoon & Surroundings Since 2008

What our customers say

At a glance

Batts work when the cavity is clean and the vapour barrier is detailed properly. Most of the performance is lost at the edges, not in the middle, so MAGNUS cuts to fit rather than compressing material into place, and seals every barrier lap and penetration.

  • Free

    Consultation to talk your job through

  • Photos

    Send photos and a specialist will reach out

  • Financing

    Available, ask at your consultation

  • Since 2008

    Insulating and repairing Saskatchewan buildings

Service area: Available in Saskatoon and within 50 km of the city, including Warman, Martensville and Delisle.

Signs you need fiberglass & mineral wool insulation

Insulation and vapour barrier go in before drywall, and the sequence matters.

Compressed material loses much of its rated performance in that spot.

Moist air passes straight through and condenses inside the wall.

Uncut batt ends leave open channels for air to move through.

Cavities were missed or the batt has slumped away from the framing.

Warm moist air is reaching cold surfaces the barrier should have protected.

Often moist indoor air condensing inside the assembly at a gap in the insulation or vapour barrier. Rule out a roof or plumbing leak first.

Planning a basement development or a renovation in Saskatoon? We can walk through batts against foam before you commit. Call (306) 880-2878 · Mon–Fri, 8am–5pm

How long it takes

Basement developmentOne to two daysDepends on square footage and layout
Single roomHalf a dayIncluding vapour barrier
Full new buildTwo to four daysCoordinated with the framing schedule

Timeframes are typical for a straightforward job and are confirmed at the consultation.

How we handle fiberglass & mineral wool insulation

1

Check the cavity

We confirm framing is square, wiring is run, and no moisture is entering before anything is installed.

2

Cut to fit

Batts are cut around wiring, boxes and pipes rather than compressed past them, which protects the rated performance.

3

Install the barrier

Vapour barrier is run continuous, lapped at framing, and sealed at every penetration and edge.

4

Seal and inspect

Boxes are poly-wrapped, seams taped, and the whole assembly checked before drywall covers it.

Ready to sort out your fiberglass & mineral wool insulation?

Serving Saskatoon. The consultation is free and there is no obligation.

What it costs

Batts are the lower-cost option per square foot. The price depends on area, the rating specified, and whether mineral wool or fiberglass suits the location. Vapour barrier and sealing are part of the quoted work, not an extra.

Material chosenMineral wool costs more and handles fire and sound better
Rating specifiedHigher rated batts cost more per square foot
Wall areaThe main driver on any batt job
Framing complexityOdd bays and obstructions slow installation
Barrier detailingNumber of penetrations to wrap and seal

We do not publish fixed prices, because the number depends on what the consultation finds.

What you get with MAGNUS

Cut, not compressed

Batts fitted around obstructions so rated performance survives installation.

Continuous barrier

Vapour barrier lapped at framing and sealed at every penetration.

Mineral wool option

Rockwool (Roxul) for better fire and sound performance where the assembly calls for it.

4,000+ projects

Experience from over 4,000 residential and commercial projects.

Licensed and insured

Business licence on file and full liability coverage.

Free consultation

Talk through batts, foam or a hybrid before anything is quoted.

Local and seasonal factors in Saskatoon

Vapour control is the part that decides whether a prairie wall lasts. Indoor air in a Saskatoon winter holds far more moisture than the outdoor air, and it will move outward through any opening left in the barrier.

That is why the sealing detail matters more than the batt itself. A wall with a perfect batt and a torn barrier will fail before a wall with an average batt and a sealed one.

Common Questions

Is fiberglass or mineral wool better for a Saskatoon basement?

Mineral wool, such as Rockwool (formerly Roxul), handles moisture and fire better and is denser for sound, which suits interior and shared walls. Fiberglass costs less and performs well in a clean, dry cavity. The decision usually comes down to budget and whether the wall has a sound or fire requirement.

Do I need a vapour barrier in Saskatchewan?

Yes. In this climate the vapour barrier goes on the warm side of the insulation, facing the interior. Without it, moist indoor air moves into the wall through winter, reaches a cold surface, and condenses inside the assembly where it cannot dry.

Why does compressing insulation reduce its performance?

Batts insulate by trapping still air in the fibres. Compressing them squeezes that air out, so a batt crushed behind a wire or pipe delivers substantially less than its label rating in that spot. Cutting to fit avoids the loss entirely.

Frequently asked questions

Batts suit clean, square, accessible cavities and cost less. Spray foam suits rim joists, crawl spaces, irregular cavities and steel buildings, because it seals as well as insulates. Many jobs use both, and we will say which applies where at the consultation.

For concrete foundation walls, premium closed-cell spray foam is often the better choice. Batts placed against cold concrete can become damp and contribute to mould. Closed-cell foam bonds to the concrete and controls air and vapour right at that cold surface. Any leaks through the foundation must be fixed first. A hybrid system, foam against the concrete with batts in the stud wall, can also be the right balance.

Yes. MAGNUS offers two full wall upgrade paths. An open interior wall upgrade removes the drywall, so the cavity can be insulated and the vapour barrier installed properly before the wall is re-boarded. An open exterior wall upgrade works from outside and preserves the interior drywall, which suits homes getting new siding. We recommend the path that fits your renovation.

It reduces airborne sound noticeably because it is denser than fiberglass. It will not make a room silent on its own. Real sound control combines dense insulation with decoupling and sealing, which is a different scope of work.

Look before the drywall goes on. Every electrical box should be wrapped, seams lapped over framing and taped, and the barrier continuous at the top and bottom plates. We invite clients to look at that stage. Photographs taken at that stage are worth keeping for any future renovation, since the barrier is invisible afterward.

Once it is installed behind a vapour barrier and drywall it is contained and stable. The precautions apply to handling it during installation, which is what protective equipment is for. Undisturbed batts in a finished wall are not a hazard.

Industry leaders in comfortable, healthy & efficient buildings

Get fiberglass & mineral wool insulation priced properly

We offer full consultations. With 7,000+ projects completed, we have seen it all and can often diagnose from photos. Send us photos and a specialist will reach out. If an on-site consultation is needed, they will let you know. Mon–Fri, 8am–5pm.