Free consultations across Saskatoon and Saskatchewan
Blown-in insulation being installed between attic trusses

Attic Insulation in Saskatoon: Top-Ups, Installs and Removals

MAGNUS installs, tops up and removes attic insulation across Saskatoon and central Saskatchewan. Most houses built before 2010 sit well under current depth, and the attic is the cheapest part of a home to correct.

Book a free consultation

We measure before we quote.

Mon–Fri, 8am–5pm

  • Award-Winning Contractor
  • Licensed & Insured
  • 7,000+ Projects Completed
  • Free Consultation
  • Financing Available
  • Serving Saskatoon & Surroundings Since 2008

What our customers say

At a glance

An attic upgrade starts with a measurement at the hatch, not a quote over the phone. We check depth, look for compression, moisture staining and gaps around ceiling penetrations, then price the work. Sealing the ceiling comes before adding depth, because leaking air undoes insulation that sits above it.

  • Free

    Consultation to talk your job through

  • Photos

    Send photos and a specialist will reach out

  • Financing

    Available, ask at your consultation

  • Since 2008

    Insulating and repairing Saskatchewan buildings

Service area: Available in Saskatoon and within 50 km of the city, including Warman, Martensville and Delisle.

Check your attic in 30 seconds

Measure the depth at the hatch, then pick what you see.
0 in24 in
What does it look like?
R-20approximate
Well short of where it should beA top-up is likely the best value upgrade in your home.
A rough guide only. Settled or compressed insulation reads lower, so we confirm the real figure at the consultation.

Signs you need attic insulation

Insulation has settled below the top of the framing, so depth is short.

Heat is escaping through the ceiling faster than the system can replace it.

Warm air in the attic is melting snow that refreezes at the cold edge.

Loose fill compacts over decades and loses performance gradually.

Air has been filtering through that spot, carrying dust with it.

Moist indoor air is reaching the cold roof deck and condensing there.

The hatch is often the single largest unsealed opening in a ceiling.

Contaminated material needs removal rather than a top-up over the top.

Want to know what depth your attic actually has before you spend anything? Book a measurement with the MAGNUS crew. Call (306) 880-2878 · Mon–Fri, 8am–5pm

How long it takes

Simple top-upA few hoursGenerally less than half a day with clear access
Air sealing and top-upUp to a full dayIncludes sealing ceiling penetrations
Removal and reinstallOne to two daysRemoval under containment adds time
Two-storey with knee wallsTwo daysSloped sections are slower to reach

Timeframes are typical for a straightforward job and are confirmed at the consultation.

How we handle attic insulation

1

Measure at the hatch

We record existing depth and material, check for moisture, and look for signs of pests or past leaks.

2

Remove if needed

Contaminated, wet or compacted material comes out under containment so it does not spread through the house.

3

Seal the ceiling plane

Light boxes, plumbing stacks, the hatch and top plates are sealed so warm air stops leaking upward.

4

Blow to depth

New material is blown in evenly and depth markers are set so the result can be verified afterward.

5

Check the venting

Soffit vents are cleared and baffles installed where needed, so the roof deck stays cold and dry.

Ready to sort out your attic insulation?

Serving Saskatoon. The consultation is free and there is no obligation.

What it costs

Attic work is priced by area, target depth and how much preparation the space needs. A clean top-up over sound material is the cheapest job in insulation. Removing contaminated fill first is what moves the number.

Attic square footageThe main driver of material and labour
Existing depthLess existing material means more to add
Removal requiredWet, contaminated or vermiculite fill must come out
Air sealing scopeNumber of ceiling penetrations to seal
AccessA small hatch or low pitch slows the work
Venting correctionsBaffles and blocked soffits addressed as found

We do not publish fixed prices, because the number depends on what the consultation finds.

What you get with MAGNUS

Depth you can verify

Markers set through the attic so finished depth is measurable afterward.

Sealed before filled

Ceiling penetrations sealed first, or the new depth underperforms.

Licensed and insured

Business licence on file and full liability coverage.

Free consultation

Talk through your attic with us before anything is quoted.

Venting checked

Blocked soffits found and cleared as part of the same visit.

Asbestos handled in-house

Extensive asbestos testing and abatement experience if vermiculite turns up.

Local and seasonal factors in Saskatoon

Saskatoon houses built through the 1960s and 1970s were insulated to a standard roughly half of what is specified today. Loose fill from that era has also settled, so the real depth is usually lower again than the original install.

Attics are the cheapest place to gain, because the work happens from above. Nothing inside the house is disturbed, and most jobs finish within a day.

Common Questions

How much attic insulation do I need in Saskatoon?

MAGNUS targets roughly R-60 in a Saskatoon attic, with R-50 as our recommended minimum. That is our recommendation for this climate rather than a universal code minimum, and it is far more than houses built before the 1980s received. The practical answer starts with measuring what is up there now, since settled loose fill often reads well below its original rating.

Should I remove old attic insulation or add on top of it?

Add on top when the existing material is dry, clean and evenly spread. Remove it when it is wet, compacted, rodent-contaminated, or when it looks like vermiculite. Adding over contaminated material seals the problem in rather than fixing it.

How long does attic insulation take to install?

A simple top-up generally takes a few hours, less than half a day. With air sealing, it can take up to a full day. Removal of old material under containment adds time, because the space has to be cleared before anything new goes in.

Frequently asked questions

Open the hatch and look across the attic floor. If the tops of the joists are visible above the insulation, depth is short. A tape measure pushed down to the ceiling drywall gives you a number in a few seconds.

Only if the air leaks are sealed too. Ice dams are caused by heat escaping into the attic, and heat escapes fastest through gaps rather than through insulation. Sealing the ceiling plane is the part that stops the melting.

It may be vermiculite, which was widely installed for decades and some of which contains asbestos. Do not disturb it and keep the hatch closed. It should be tested before anyone works up there, and removal is a controlled process. MAGNUS has extensive experience with asbestos testing and professional abatement, so the testing, removal and new insulation can all be handled by one team.

Some insulation settles over time, and how much depends on the material. Modern loose fill is blown to a depth that accounts for expected settling, and depth markers let you verify the result. We recommend an attic inspection roughly every ten years to check depth, moisture and ventilation.

Yes, and winter is a practical time for it because the attic is cold and comfortable to work in. Summer attics reach temperatures that limit how long a crew can safely stay up there. Scheduling is often easier in winter too, because the busiest months for attic work are the autumn ones.

If you store items in the attic, they need to be moved before we start. We will tell you at the consultation whether the storage area can be kept usable, which usually means building a raised platform above the new depth.

Industry leaders in comfortable, healthy & efficient buildings

Get attic insulation priced properly

We offer full consultations. With 7,000+ projects completed, we have seen it all and can often diagnose from photos. Send us photos and a specialist will reach out. If an on-site consultation is needed, they will let you know. Mon–Fri, 8am–5pm.